Jump to content

PSA: Don't try stripping minis with lacquer thinner


Evil Eye

Recommended Posts

I had a whole bundle of rather badly painted Gaunts from my early days in the hobby and thought it'd be a good idea to try restoring them to grey plastic, with the intent of repainting them better. To do this, I took my ultrasonic cleaner and used a roughly 3 parts lacquer thinner to 7 parts water mixture to fill it with, before dunking the models into the thing to soak for a bit. Lid on, button pressed, waited a bit...

 

...Returned to find the diluted thinner was still strong enough to melt not only the paint, but also the plastic of the miniatures AND THE PLASTIC BASKET INSIDE THE CLEANER.

 

I'm currently letting the cleaner and its contents soak with water in the hope of at least avoiding any further damage to the cleaner. I suspect the Gaunts are toast (or rather, syrup) at this point though. Fortunately they were not a great loss, as they were painted thicc, but even so. Let this be a cautionary tale not to use lacquer thinner as a stripper, even diluted.

 

With that being said, what's a good thing to put in an ultrasonic cleaner to strip miniatures without turning them into mush?

Link to comment
Share on other sites

Biostrip 20 is great, just put the minis in the pot overnight then rinse them in water.

 

After that a quick run through the Ultrasonic cleaner with water and maybe a little detergent just to get any residue off.

 

Rik

100% biostrip. I've left models in there for a few months and they're fine. Get the 750ml spray bottle, a old ice cream tub or something and a old toothbrush. It's amazing stuff.

Link to comment
Share on other sites

Yeah, lacquer thinner is nasty stuff (will eat rubber seals on airbrushes) :(

 

As an alternative, isopropyl alcohol works really well. :) (although it is flammable, so don't put it in an ultrasonic cleaner unless you want to create a bomb... there again, I've found just dipping the model in it and then brushing it with a toothbrush was enough)

Link to comment
Share on other sites

Hey Evil!

 

I could be wrong, but I think lacquer thinners are basically just acetone and some extra nasty stuff to make it more effective - definitely not something to strip plastic with! I also seem to recall reading that ultrasonic cleaners can create small sparks that make using flammable substances in them dangerous!

 

Either way, my suggestion would be isopropyl alcohol. I wrote a thing about it a while ago here. =]

In general time is your friend - you can get it to work almost instantly, but the longer you leave something soaking in iso the easier it is to remove the paint. I've got a tub that's been sat for more than a year now - the models aren't damaged or weakened at all, but you only have to look at the paint and it falls off!

Link to comment
Share on other sites

  • 2 weeks later...

Yeah, lacquer thinner is nasty stuff (will eat rubber seals on airbrushes) :sad.:

 

As an alternative, isopropyl alcohol works really well. :smile.: (although it is flammable, so don't put it in an ultrasonic cleaner unless you want to create a bomb... there again, I've found just dipping the model in it and then brushing it with a toothbrush was enough)

 

Wait wait. Is there some risk of igniting things with an ultrasonic cleaner?

Link to comment
Share on other sites

 

 

Yeah, lacquer thinner is nasty stuff (will eat rubber seals on airbrushes) :sad.:

 

As an alternative, isopropyl alcohol works really well. :smile.: (although it is flammable, so don't put it in an ultrasonic cleaner unless you want to create a bomb... there again, I've found just dipping the model in it and then brushing it with a toothbrush was enough)

Wait wait. Is there some risk of igniting things with an ultrasonic cleaner?

The vapor-phase is the issue with many of the dangers we face in the hobby. Lacquer, oil thinners, etc all have low vapor-phase pressures so they enter into the gas phase more readily. This creates an area of gas above the liquid and gas is more prone to ignition than liquid for a variety of reasons (fun fact: candles rely on this to burn gas, while the wick provides a steady supply of liquid to replace what was lost to the gas phase). Enough agitation can provide the energy to ignite a gas phase, but it’s a simple fix of letting the gas disperse into the atmosphere. Just don’t use a closed container.

Edited by jaxom
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.